A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

在二元柔壁自适应风洞中利用面元法进行三元模型实验

简要叙述了在西北工业大学二元柔壁自适应风洞中利用面元法进行二元半机翼模型试验的研究情况，分析了面元法的基本思想和部分试验结果。     

锥柱形加筋金属膜片变形的数值仿真分析

概述了金属膜片贮箱膜片结构的研究现状,提出了锥柱形加筋膜片整体结构变形问题。根据试验情况建立了该膜片的有限元模型,并基于非线性有限元软件MSC.Marc进行了数值模拟,分析了膜片结构的变形过程和变化规律,通过对加筋结构的分析解释了膜片变形的机理,得到了一些控制膜片失效的方法。     

随振动量级增加卫星结构频率下移的分析

对卫星振动频率随量级增加而出现下降，即振动频率“漂移”的现象进行了初步分析。发现随振动量级的增加。结构的非线性表现突出。结构的刚度下降和阻尼增加，可认为主要是由蜂窝材料的非线性因素所致。     

翼板颤振主动抑制的无限维非线性分析

 <正> 1.混合动力学系统的Hopf分叉定理 本文将Marsden-McCracken关于分布参数的Hopf分叉定理推广至混合动力学系统。 设在积空间X=E×R~n中依赖参数μ的演化方程为     

双轴应力下含裂纹加筋曲板剩余强度的弹塑性有限元计算

 采用考虑了大应变的弹塑性有限元方法,以裂纹尖端张开角为断裂准则,实现了双向受载条件下加筋曲板中裂纹起裂到失稳整个扩展过程的数值模拟计算;还对与加筋曲板有同样尺寸的加筋平板进行了分析和计算。结果表明,所提出的分析方法和所采用的断裂准则适用于对含裂纹加筋结构所进行的剩余强度分析。     

刚度导数法在含裂纹铆接加筋板应力强度因子计算中的应用

本文探讨了刚度导数法用于含裂纹铆接加筋板应力强度因子计算的问题。提出了选取对刚度导数矩阵有贡献元素的一种新方法,成功地解决了裂尖位于筋条轴线附近时,采用刚度导数法计算应力强度因子的困难。算例结果表明,本文提出的方法是正确有效的。文中还阐述了刚度方程降阶的方法,这种方法对于应用小容量计算机求解较大的结构分析问题,有一定的参考价值。     

典型加筋板的优化设计

对飞机结构设计中典型加筋板优化设计问题进行了研究 ,对典型加筋板形式、优化问题、计算方法和优化策略进行了描述 ,编写了优化设计程序 ,并进行了算例考核。计算结果表明 ,优化设计结果合理 ,可对该类加筋板的结构设计提供参考和指导。     

运载火箭阻尼安装板的设计

 <正>运载火箭在起飞和着陆时的瞬态载荷和飞行过程中的气动力的随机激励都是宽频带的。在这种环境中安装精密仪器的仪表板若采用过去常规的橡皮减振器减振已很难保证在较宽频带内都能起到应有的减振作用。利用阻尼材料做成的夹层板减振，国内外已做了大量的工作^[t~3]，取得了较为明显的效果。本文针对产品设计中要解决的减振问题，提出了设计思想、计算分析与试验方法。     

简谐激励下弯曲薄板的非线性运动方程

推导了两端固定和两端简支的弯曲薄板在其支承简谐激励下的运动微分方程,并利用Galerkin方法对其进行了离散化处理。